Tips for Water Heater Energy Efficiency

Home owners who have hot water heater at home are surely looking for ways on how to save energy. A lot of researches show that one of the main contributors of increase in the energy bill is the use of hot water at home. With this, it is necessary to know some ways on how to be energy efficient when it comes to the use of this heating system.

Below are tips on energy efficiency with water heater:

Going for Tankless Unit

If you still use the traditional tank type water heating system at home, it would be more convenient and energy efficient when you replace it with a tankless unit. This tankless heater heats water on demand so it helps you save a lot of energy. This is the opposite of how tank type works where water is constantly heated even if it is not used.

Some might be hesitant to go for this tankless unit due to its initial cost. But, definitely you will enjoy its many benefits in the long run.

Setting the Temperature

If the temperature of your hot water is high it consumes more energy compared to when it is set in a lower temperature. Certainly you don’t need a very hot water so try to lower the temperature to about 120 degrees.

This practice will not only help you save energy but it could also help avoid any scalding accidents. Make sure that you also constantly check the temperature of your hot water to avoid setting it too high.

Proper Insulation of the Water Heater

The water heater unit could save a lot of energy when it is properly insulated.  This insulation also helps prevent CO2 from going into the air. See to it that you use the right type of insulation for the unit by referring to the manufacturer’s manual.

See to it that every visible pipe you see going towards or away from your water heater is proper covered. When you have a gas water heater, make sure that the insulation is not too close to the source of heat.
Strategic Location of the Heater

Before installation of your water heater, check your home for the area where there is high demand of hot water. If you reduce the travel time of hot water, it helps you save more energy.

Proper Maintenance

You certainly are not capable of doing an overall maintenance of your water heating system. With this, it is very important that you schedule maintenance for your heater at least once a year.

For all your water heater service needs, call Los Angeles Plumbing. We are pretty sure that we could handle the services you need for your water heater. Our plumbers utilize the right tools and equipment to do their job fast and efficiently. You could be sure that we are always ready for any emergency service.

How to Keep Tree Roots from Your Sewer Line

When your sewer line has some cracks or leaks, it is not anymore a surprise that tree roots would grow towards it. This is due to the water content in this line and we know for sure that roots are attracted to water. It is important that homeowners have some ideas on how to keep these from causing damage in your sewer lines and prevent expensive repairs.

Effects of tree roots in Drain lines

  •          broken pipes
  •          clog or blockage
  •          sewer backup
  •          damaged pipes

When a leak happens due to these roots, it could lead to health issues. This is the reason why it has to be addressed fast. The problem is dealing with damages caused by tree roots is very expensive. With this, it is best to prevent these tree roots from causing you a lot of headaches.

Determine Where Sewer Lines Are Located

Tree roots caused problems in the sewer lines for homeowners are not careful with where they plant some trees in their yard. If ever you do not know where your sewer lines are buried, you could get a professional service to help you identify where these lines are.

With this, if you have plans of planting trees in your garden, you know where you place it which will not cause any problem on your sewer. Also, you could avoid making some expensive landscaping right above these lines so that it will not be damaged when repairs are needed.

Create a Hurdle between Lines and Trees

To make sure that you avoid expensive repair and damages due to problems of tree roots in drain lines, you could ask some professional plumbers to create a barrier between trees and the sewer lines in your yard. This will definitely stop roots from going to your lines.

There are now also some chemicals that you could use to stop the growth of roots in a certain area. See to it that you read the instruction of these products carefully to avoid any troubles.

Think Well Before Planting

The best way that you could prevent tree root issues is to plant trees away from your sewer lines. If ever you wanted to add some plants near it, make sure that these plants do not have large and strong roots. So that it could not damage your lines and if ever it gets inside your drains, dealing with it is easy.

It is also advised to get your sewer lines properly inspected at least once a year in order to see if tree roots are starting to cause troubles. If you need help in dealing with tree roots in your lines, call Los Angles Plumbing. We have the right tools and equipment to do the inspection and also perform the needed maintenance to prevent clogs and other drain issues from frequently happening.

Tags :

Video Line Inspection – Finding the Source of the Problem in your Plumbing Lines

Inspecting the sewer lines in your home is definitely not an easy job. Good thing that professional plumbers today use latest technology called video line inspection. With this, inspecting plumbing lines have become faster and easier. Finding the source of a certain plumbing issues is now pretty easy to do.

Fast Diagnosis of Video Inspection

Today, the best way to find the location of a certain issue in a plumbing line is through video inspection. It uses a specialized camera that will be inserted in the plumbing lines and it feeds video information to the plumber.

Before this technique was utilized, most plumbers are just doing guesswork. They dig up a certain part of your property without the assurance that the problem is near the area. This makes dealing with the problem expensive and time-consuming.

When you have a certain problem in your plumbing, it is very important that it is diagnosed fast. With this, you prevent any expensive damages in your property such as damages due to flooding.

A plumbing issue brings a lot of inconvenience to homeowners. This is why immediate action is needed. The problem has to be stopped before the problem escalates to another level.

Assessing Any Plumbing Issue with Video Inspection

The good thing about video line inspection is it could thoroughly diagnose your plumbing lines. It could see if your lines have leaks, cracks, clogs and it could even provide you with information on the current condition of your pipes. With this, homeowners will know if it has to be replaced.

After a video inspection, a plumber could immediately propose ways on how to deal with the existing problem and also they could tell you if your pipes need replacement.

Giving You the Big Picture inside Your Pipes

You don’t want temporary fixes to deal with major issues in your plumbing. This is the reason why you need to find the exact location of the problem.

Since the video inspection could give plumbers a clear idea on what is the condition of the plumbing lines, they could easily recommend a long-term solution to the problem. After their service, you won’t experience any problem for a long time.

The next time you experience a problem in your drain lines; do not forget to seek video line inspection service. A lot of plumbing companies use this technology today for it also helps them do their job better and faster.

In order to reap the many benefits of this service, go for the service of licensed and professional plumbers. They could help you better in a timely manner.

For a professional video line inspection service, go for Los Angeles Plumbing. We have been in the industry for a long time. Our plumbers are well-experienced and trained well in order to effectively offer any plumbing service such as video inspection. The latest facilities and tools we use give us the advantage. Call us now so that we could immediately check your plumbing lines and deal with any problem that is in it.

Tags :

Phases of Garbage Disposal Installation

Proper garbage disposal installation and service should follow specific phases to ensure fewer breakdowns in the future.

Proper Unit Wiring

Depending on the manufacturer and type of garbage disposal unit you may have, some will come with wiring attached and others may not.  If the wires for your unit are not attached, you would have to remove the unit cover plate and connect the wires using the instructions in the owner’s manual from the manufacturers.

Generally, wires will be color coded, which means that you simply need to match the colors.  Do not assume this though and still rely on what the manual says.  After completely attaching all the wires, make sure that the cover plate is securely screwed back on to protect the internal components.

The Drain Flange

Once the wires are in order, the drain flange and matching mounting ring should be installed.  Plumber’s putty should be applied to the underside of the drain flange under the sink.  Make sure that the plumber’s putty is approximately half and inch thick and about 10 inches in length.

The flange should be inserted into the drain hole and pressed down evenly to make sure that it attaches properly.  The backup ring should then be snapped on together with the mounting ring and fiber gasket.

Work on alternate sides with a screwdriver to ensure that the mounting ring fits tightly against the sink.  When it is tightened evenly, you will observe some of the plumber’s putty will be squeezed out from the flange.  Trim it away with a knife.

Mounting and Connecting

The disposal can be mounted into the mounting ring at this point.  It is important to make sure that the disposal outlet faces the drain pipe connection before you tighten the disposal into place.

The disposal should then be connected to the P-trap by measuring the discharge pipe and cutting it to size.  Use the hacksaw to create a clean cut that will easily attach to the garbage disposal outlet.  Follow the instructions in the owner’s manual to make a proper connection.

The dishwater discharge tube should also be connected at this point.

Testing the Disposal

Once everything has been mounted and connected, the next phase is to test everything to make sure there are no leaks or any other problems.

Turn on the power to the garbage disposal unit.  Let water run into the sink and operate the garbage disposal unit.  Allow the unit to fill up with water a bit before operating it.

While the garbage disposal unit is running, check underneath to verify there are no leaks.  Feed the unit some food waste to ensure that everything is disposed of correctly.

Call Los Angeles Plumbing today for

Professional Repair of Slab Leaks

No matter whether you are dealing with leak repairs, both in and out of slabs, it pays to make sure that professionals are on the job.

Confirming the Source of Leaks

Any professional plumbing contractor understands that the basic step in repairing leaks is to confirm its source.  The good news is that professional plumbers are properly trained and equipped to pinpoint accurately the source of leaks.

Leak detection can also be carried out by homeowners, but without the proper training and equipment, this would mostly be a hit and miss detection procedure.

The best way to make sure that the source of leaks is properly confirmed is to have professionals come in and check the home plumbing system.

Usually when it comes to slab leaks, homeowners should check with their insurance providers.  It is not uncommon for many homeowners to be surprised that they are actually covered against flooding and similar damages that can be the result of slab leak repairs.

Repair Procedure for Leaks

Once the source of leaks has been determined, professional plumbers are now in a better position to make the necessary and proper repairs.  Water supply to the entire area or the home will be turned off until repairs are completed.

For slab leaks, the flooring material would be removed from the area where the source of the leak has been detected.  Only the necessary materials will be removed to make sure that cost of repair and replacements are kept at a minimum.

Holes will be drilled on the 4-inch concrete slab to create an initial opening to reach the affected portion of the plumbing system.  Once the source has been confined to a specific area, the access hole will be made bigger to make the necessary repairs.

A cutting tool will be used to remove the damaged portion of the pipe.  When replacing sections of home plumbing pipes, it is important that the same time of material is used.  Usually, it can be either PVC or copper piping.

Copper pipes should be welded, which means the access area must be left exposed for a few days to verify that the leak has been fixed correctly.

Covering the Access Hole

After the repair work has been done and the replacement pipe has been tested, the access hole must be covered up completely to finalize the repair.

Concrete will be mixed, poured, and evened out to match the existing surrounding slabs.  The area must be cured for a number of days before it is completely covered up to ensure that the cement mixture has hardened completely.

We can handle leak repairs, both in and out of slabs to ensure that your problem is solved properly. Call Los Angeles Plumbing today!

Restoring Water Pressure in Homes

Restoration of water pressure in homes can be done with a few simple and practical steps.

Addressing Water Leaks

It should be understood that one of the major causes of low water pressure is if there is a leak in your plumbing system.  Keep in mind that plumbing systems are designed to keep water in using a series of interconnected pipes.  When pipes spring a leak or crack, the integrity of the water pressure significantly decreases.

Regularly checking your pipes will give you an indication of possible leaks.  This will allow you to initiate the necessary repairs.  Replacing cracked or damaged pipes is one of the most effective ways to restore water pressure.

The water meter is an excellent way to judge whether there is a leak in your plumbing system or not.  Simply take note of the reading when no water fixture is being used.  Do this every two hours to see if there are changes in the reading; this will let you know if there is a leak in your plumbing system.

Eliminating Mineral Deposits

One of the most common reasons why mineral deposits start to buildup is the use of hard water.  When this condition happens, you can expect the buildup to create obstruction in your faucets, showerheads, and other plumbing fixtures.  This will lead to poor water pressure distribution.

Mineral deposit buildup can also significantly reduce the inner diameter of your plumbing pipes.  The reduced path of water will hamper its smooth flow resulting in poor water pressure that can be experienced throughout your household.

Cleaning your faucets and showerheads is a good way to remove mineral buildup on plumbing fixtures.  However, if the buildup is within the pipes, you will need professional help to restore the water pressure in your home to respectable levels.

We can help you verify if mineral deposits is the cause of your water pressure problems.  We can recommend effective solutions that you can choose from.

When All Else Fails

The fastest and easiest way to restore water pressure in your home is to call for professional help.  We have properly trained and licensed professional plumbers that can do the job in an instant.  We can carry out tests that will give you the right solution to your water pressure woes.

The reality is that there are some problems that only we can deal with.  Corrosion of pipes, major cracks and leaks, or major blockage in your water supply line are some examples of issues that contribute to poor water pressure that only trained professionals can handle properly.  If you need restoration of water pressure immediately, we can do the job for you. Call Los Angeles Plumbing today!

Bringing Your Home Up to Code

Licensed professional plumbers are your best choice to implement updates to plumbing systems so they are up to code.

Significant Changes to Plumbing Codes

According to the Plumbing Engineer, some of the most notable changes in plumbing code involve updates in energy and water conservation.  Although there are previous provisions already, the updates are meant to present amendments to cover technological advancements in the industry.

Significant changes that professional plumbers have been updated with on prevailing plumbing codes includes the:

  • Minimum number of plumbing fixtures per occupancy
  • Water consumption
  • Revised application
  • Backflow and material requirements for fixtures
  • Requirements for alternative water sources
  • Sustainable practices on water heating and consumption
  • Revised fuel gas purging
  • Revised vacuum drainage system requirements
  • Updated joint and connection requirements
  • Standards for water supply and drainage piping

Plumbing System Components

In ensuring that your plumbing system remains up to code, you must take note of its various elements.  Based on the Healthy Housing Reference Manual of the Center for Disease Control and Prevention, the main purpose of the plumbing system should be to deliver adequate potable hot and cold water supply to residents of a household.  The plumbing system should also be able to drain all sewage discharge and wastewater generated by plumbing fixtures into a public or private sewer disposal system.

This definition gives you a general idea of the components of the plumbing system that will come under close scrutiny from housing inspectors.  Any inadequacies in the plumbing system will be a violation of the code and can give you corresponding fines and penalties.  This emphasizes the value of professional plumbing contractors who are updated with such codes and can make sure that all installations, repairs, and maintenance work will pass any type of inspection.

Efficiency of Water Service

Updates to plumbing systems should take into account the drive to increase its efficiency in every household.  It is highly recommended that piping of house service lines must be made as short as possible.  This means that elbows and bends should be used at a minimum because they can substantially reduce the effective water pressure in your pipes and plumbing fixtures.

Los Angeles Plumbing is also updated on the fact that the house service line must be protected from freezing by burying it under at least four feet of soil.  The depth of course may vary depending on your actual location.  Local or State plumbing codes have a more accurate recommendation.

To ensure that your plumbing system is up to date with existing codes, it is necessary to ensure that the size of the service line should be at least ¾ inch.

The minimum water pressure in an average household should not be less than 40 pounds per square inch (psi).

Materials for house service should be approved copper, plastic, steel, cast iron, or wrought iron.  Cement or concrete joints should not be used and glue joints between various types of plastic must be avoided.  Female threaded PVC fitting must not be used as well.


- William
I was worried that those tree roots would ruin my entire sewer system. I thank this plumbing company for helping with video inspection. They helped me see and solve the problem.

Recent Post